MINI Factory OEM replacement DUAL MASS Flywheel for the Cooper S with the 6-speed manual transmission.

If you are looking to replace the Clutch AND the Flywheel, take a look at the factory Clutch & Flywheel Service Kits, or the lower costAftermarket Clutch & Flywheel Service Kit.

Fits the following Cooper S models with the Manual Transmission:

2007-2010 R56 MINI Cooper S Hardtop
2008-2010 R55 MINI Cooper S Clubman
2009-2010 R57 MINI Cooper S Convertible

NOTES:

• MINI spedifies new Flywheel Bolts when servicing the Flywheel. Bolts available separately.
• The Dual Mass Flywheel should NOT be re-surfaced. It can be re-used for one clutch change provided the surface is in good condition. Some shops may offer to re-surface the dual mass flywheel, but we have seen reports of short-term problems and driveability issues when re-surfaced - more often than not.

Torque sequence for Flywheel Bolts - use criss-cross pattern:

1. Stage 1 - 8 Nm (6 ft-lb)
2. Stage 2 - 30 Nm (22 ft-lb)
3. Stage 3 - Additional 90º

For other models, see G2NMG7600-P.

For JCW models, see G2NMG7605.

For the Factory Remanufactured Clutch Kit, see G2NMG7610.

For Performance Clutch/Flywheel kits, see G2NMG1640.

For Performance Clutch kits, see G2NMG1601.

Fits the following JCW models with the N14 Engine and Manual Transmission:

2007-06/2012 R56 JCW MINI Cooper S Hardtop
2008-06/2012 R55 JCW MINI Cooper S CLUBMAN
2009-07/2012 R57 JCW MINI Cooper S Convertible
2012-07/2012 R58 JCW MINI Cooper S Coupe
2012-06/2012 R59 JCW MINI Cooper S Roadster

NOTE: The Dual Mass Flywheel should NOT be re-surfaced. It can be re-used for one clutch change provided the surface is in good condition. Some shops may offer to re-surface the dual mass flywheel, but we have seen reports of short-term problems and driveability issues when re-surfaced - more often than not.

For the Factory replacement Flywheel Bolts, see G2NMG7603.

Torque sequence for Flywheel Bolts - use criss-cross pattern:

1. Stage 1 - 8 Nm (6 ft-lb)
2. Stage 2 - 30 Nm (22 ft-lb)
3. Stage 3 - Additional 90º

For the Factory Remanufactured Clutch Kit for JCW models, see G2NMG7612.

For Performance Clutch/Flywheel kits, see G2NMG1640.

For Performance Clutch kits, see G2NMG1601.

For the Factory Remanufactured Clutch Kit for non-JCW models, see G2NMG7610.

MINI Factory OEM replacement Flywheel for the MINI Cooper and Cooper S with the Automatic Transmission.

Fits the following models with the Automatic Transmission:

2007-2013 R56 MINI Cooper and Cooper S Hardtop
2008-2014 R55 MINI Cooper and Cooper S Clubman
2009-2015 R57 MINI Cooper and Cooper S Convertible
2012-2015 R58 MINI Cooper and Cooper S Coupe
2012-2015 R59 MINI Cooper and Cooper S Roadster
2011-2016 R60 MINI Cooper and Cooper S Countryman
2013-2016 R61 MINI Cooper and Cooper S Paceman

Torque sequence for Flywheel Bolts - use criss-cross pattern:

1. Stage 1 - 8 Nm (6 ft-lb)
2. Stage 2 - 30 Nm (22 ft-lb)
3. Stage 3 - Additional 90º

For the Factory Remanufactured Clutch Kit, see G2NMG7610.

For Performance Clutch/Flywheel kits, see G2NMG1640.

For Performance Clutch kits, see G2NMG1601.

Fits the following JCW models with the N18 Engine and Manual Transmission:

06/2012-2013 R56 JCW Cooper S Hardtop
06/2012-2014 R55 JCW Cooper S CLUBMAN
07/2012-2015 R57 JCW Cooper S Convertible
07/2012-2015 R58 JCW Cooper S Coupe
06/2012-2015 R59 JCW Cooper S Roadster
2011-2016 R60 JCW Cooper S Countryman
2013-2016 R61 JCW Cooper S Paceman 

NOTE: The Dual Mass Flywheel should NOT be re-surfaced. It can be re-used for one clutch change provided the surface is in good condition. Some shops may offer to re-surface the dual mass flywheel, but we have seen reports of short-term problems and driveability issues when re-surfaced - more often than not.

Torque sequence for Flywheel Bolts - use criss-cross pattern:

1. Stage 1 - 8 Nm (6 ft-lb)
2. Stage 2 - 30 Nm (22 ft-lb)
3. Stage 3 - Additional 90º

For the Factory Remanufactured Clutch Kit for JCW models, see G2NMG7612.

For Performance Clutch/Flywheel kits, see G2NMG1640.

For Performance Clutch kits, see G2NMG1601.

MINI Factory OEM replacement SINGLE MASS Flywheel for the Cooper (non-S) with the 6-speed manual transmission.

If you are looking to replace the Clutch AND the Flywheel, take a look at the factory Clutch & Flywheel Service Kits.

Fits the following Cooper (non-S) models with the Manual Transmission:

2007-2013 R56 MINI Cooper Hardtop
2008-2014 R55 MINI Cooper Clubman
2009-2015 R57 MINI Cooper Convertible
2012-2015 R58 MINI Cooper Coupe
2012-2015 R59 MINI Cooper Roadster
2012-2016 R60 MINI Cooper Countryman
2013-2016 R61 MINI Cooper Paceman

NOTE: MINI specifies new Flywheel Bolts when servicing the Flywheel. Bolts available separately.

Torque sequence for Flywheel Bolts - use criss-cross pattern:

1. Stage 1 - 8 Nm (6 ft-lb)
2. Stage 2 - 30 Nm (22 ft-lb)
3. Stage 3 - Additional 90º

For other models, see G2NMG7600-P.

For JCW models, see G2NMG7605.

Flywheel Bolts available separately in a set of 6 bolts.

For the Factory Remanufactured Clutch Kit, see G2NMG7610.

For Performance Clutch/Flywheel kits, see G2NMG1640.

For Performance Clutch kits, see G2NMG1601.

MINI Factory OEM replacement DUAL MASS Flywheel for the Cooper S with the 6-speed manual transmission.

If you are looking to replace the Clutch AND the Flywheel, take a look at the factory Clutch & Flywheel Service Kits, or the lower cost Aftermarket Clutch & Flywheel Service Kit.

Fits the following Cooper S models:

2011-2013 R56 MINI Cooper S Hardtop
2011-2014 R55 MINI Cooper S Clubman
2011-2015 R57 MINI Cooper S Convertible
2012-2015 R58 MINI Cooper S Coupe
2012-2015 R59 MINI Cooper S Roadster
2011-2016 R60 MINI Cooper S Countryman
2013-2016 R61 MINI Cooper S Paceman

NOTE: The Dual Mass Flywheel should NOT be re-surfaced. It can be re-used for one clutch change provided the surface is in good condition. Some shops may offer to re-surface the dual mass flywheel, but we have seen reports of short-term problems and driveability issues when re-surfaced - more often than not.

Factory specifies new Flywheel Bolts - available separately.

Torque sequence for Flywheel Bolts - use criss-cross pattern:

1. Stage 1 - 8 Nm (6 ft-lb)
2. Stage 2 - 30 Nm (22 ft-lb)
3. Stage 3 - Additional 90º

For JCW models, see G2NMG7605.

For the Factory Remanufactured Clutch Kit, see G2NMG7610.

For Performance Clutch/Flywheel kits, see G2NMG1640.

For Performance Clutch kits, see G2NMG1601.